Getting your brightest ideas off the ground®


        
      COMPANY profile

       standard

       coating system

      OUR commitment

      Terms and Conditions

      Warranty

      ONLINE CATALOG

      Contact Us


RTSE
Roadway Lighting Standard with Tapered Upsweep Arm
Pole Shaft
The pole shaft is one or two section design, each section being fabricated from standard 11 gauge (0.1196"), 7 gauge (0.1793"), or 3 gauge (0.2391") steel. The pole shaft material is a weldable grade hot rolled commercial quality carbon steel with a guaranteed minimum yield strength of 55,000 psi after fabrication. Each section is one-piece construction with a full length longitudinal weld and is cylindrical in cross-section having a uniform taper of 0.14 inches of diameter change per foot of length.
Base Plate
The anchor base is fabricated from structural quality hot rolled carbon steel plate that meets or exceeds a minimum yield strength of 36,000 psi. The anchor base telescopes the pole shaft and is circumferentially welded top and bottom. All welds are performed in accordance with the American Welding Society specification AWS D1.1, latest edition.
Anchor Bolts
Anchor bolts are fabricated from commercial quality hot rolled carbon steel bar that meets or exceeds a minimum yield strength of 55,000 psi. Four properly sized anchor bolts, each with two regular hex nuts and washers, are furnished and shipped with all poles unless otherwise specified. Anchor bolts shall have the threaded end galvanized a minimum of 8 inches in accordance with ASTM A-153. Fully galvanized anchor bolts are available upon request.
Handhole
An oval reinforced gasketed handhole, having a nominal 3" x 5" or 4" x 6-1/2" inside opening, located 1'-6" above base, is standard on all poles. Optional 5" x 8" and 4" x 10" handholes are available (see options). A grounding location is provided inside the handhole ring.
Finishes
The Standard Finish is a polyester thermosetting powder coating applied to the surface of the substrate to a minimum of 3 mils for all color finishes. Hot dip Galvanized finish to a ASTM A-123 specification or primed finish is also available. For optional finishes, see K-KLAD and K-KLAD Over Galvanizing.
Design
All KW Industries, Inc. Roadway Lighting Standards (RTS) and luminaire arms meet or exceed all American Association of State Highway and Transportation Officials (AASHTO) wind loading specifications for roadway standards.

HOW TO ORDER
When ordering KW Roadway Lighting Standards (RTS), luminaire arms and accessories, be sure to specify the complete catalog number. Our catalog numbers reflect the precise specifications of the item ordered to ensure our customers will receive the product which meets their exact requirements.
The following explanation of the catalog numbers will be helpful in placing orders:

CATALOG LOGIC - ORDERING SAMPLE

Catalog Number Mounting
Height 		Base
Diameter 		Gauge Handhole
Size 		Anchor Bolt Bolt
Circle 		Ship
WT. 		Select
RTSE20-6.1-11206.1113 x 5.00.75 x 30 x 39.5149Configure
RTSE20-6.5-11206.5114 x 6.51.00 x 36 x 49.5205Configure
RTSE25-6.1-11256.1113 x 5.00.75 x 30 x 39.5173Configure
RTSE25-6.5-11256.5114 x 6.50.75 x 30 x 39.5204Configure
RTSE25-7.0-11257.0114 x 6.51.00 x 36 x 410230Configure
RTSE30-7.0-11307.0114 x 6.51.00 x 36 x 410253Configure
RTSE30-7.5-11307.5114 x 6.51.00 x 36 x 410.5265Configure
RTSE30-8.0-11308.0114 x 6.51.00 x 36 x 411293Configure
RTSE30-8.5-11308.5114 x 6.51.00 x 36 x 411.5309Configure
RTSE30-9.0-11309.0114 x 6.51.00 x 36 x 412.5331Configure
RTSE30-10.0-113010.0114 x 6.51.00 x 36 x 413.5424Configure
RTSE35-7.5-11357.5114 x 6.51.00 x 36 x 410.5283Configure
RTSE35-8.0-11358.0114 x 6.51.00 x 36 x 411311Configure
RTSE35-8.5-11358.5114 x 6.51.00 x 36 x 411.5338Configure
RTSE35-9.0-11359.0114 x 6.51.00 x 36 x 412.5358Configure
RTSE35-9.0-7359.074 x 6.51.25 x 42 x 612.5534Configure
RTSE35-10.0-113510.0114 x 6.51.00 x 36 x 413.5458Configure
RTSE40-9.0-11409.0114 x 6.51.00 x 36 x 412.5376Configure
RTSE40-9.0-7409.074 x 6.51.25 x 42 x 612.5597Configure
RTSE40-10.0-114010.0114 x 6.51.00 x 36 x 413.5480Configure
RTSE40-11.0-74011.074 x 6.51.25 x 42 x 615720Configure





RTSE SINGLE ARM LUMINAIRES
ARM WIND RTSE 20 RTSE 25 RTSE 30 RTSE 35 RTSE 40
16PS 80 20-6.1-11
20-6.5-11		 25-6.1-11
25-7.0-11		 30-7.0-11
30-7.5-11
30-8.0-11		 35-7.5-11
35-8.0-11
35-8.5-11		 40-8.5-11
40-9.0-11
90 20-6.1-11
20-6.5-11		 25-6.1-11
25-7.0-11		 30-7.0-11
30-7.5-11
30-8.0-11		 35-7.5-11
35-8.0-11
35-8.5-11		 40-8.5-11
40-9.0-11
100 20-6.1-11
20-6.5-11		 25-6.1-11
25-7.0-11		 30-7.5-11
30-8.0-11		 35-7.5-11
35-8.0-11
35-8.5-11		 40-8.5-11
40-9.0-11
18PS 80 20-6.1-11
20-6.5-11		 25-6.1-11
25-7.0-11		 30-6.8-11
30-7.0-11
30-7.5-11
30-8.0-11		 35-7.5-11
35-8.0-11
35-8.5-11		 40-8.5-11
40-9.0-11
90 20-6.1-11
20-6.5-11		 25-6.1-11
25-7.0-11		 30-6.8-11
30-7.0-11
30-7.5-11
30-8.0-11		 35-7.5-11
35-8.0-11
35-8.5-11		 40-8.5-11
40-9.0-11
100 20-6.1-11
20-6.5-11		 25-6.1-11
25-7.0-11		 30-7.5-11
30-8.0-11		 35-7.5-11
35-8.0-11
35-8.5-11		 40-8.5-11
40-9.0-11
110PS 80 20-6.1-11
20-6.5-11		 25-6.1-11
25-7.0-11		 30-7.0-11
30-7.5-11
30-8.0-11		 35-7.5-11
35-8.0-11
35-8.5-11		 40-8.5-11
40-9.0-11
90 20-6.1-11
20-6.5-11		 25-6.1-11
25-6.5-11
25-7.0-11 		30-7.0-11
30-7.5-11
30-8.0-11		 35-7.5-11
35-8.0-11
35-8.5-11		 40-9.0-11
40-10.0-11
100 20-6.1-11
20-6.5-11		 25-6.5-11
25-7.0-11
25-7.5-11 		30-7.0-11
30-7.5-11
30-8.0-11 		35-7.5-11
35-8.0-11
35-8.5-11		 40-10.0-11
40-9.0-7
112PS 80 20-6.1-11
20-6.5-11		 25-6.1-11
25-7.0-11
25-7.5-11 		30-7.0-11
30-7.5-11
30-8.0-11		 35-7.5-11
35-8.0-11
35-8.5-11		 40-8.5-11
40-9.0-11
90 20-6.1-11
20-6.5-11		 25-6.5-11
25-7.0-11
25-7.5-11 		30-7.0-11
30-7.5-11
30-8.0-11		 35-8.0-11
35-8.5-11
35-9.0-11		 40-9.0-11
40-10.0-11
100 20-6.1-11
20-6.5-11		 25-6.5-11
25-7.0-11
25-7.5-11 		30-7.0-11
30-7.5-11
30-8.0-11		 35-8.0-11
35-8.5-11
35-9.0-11		 40-10.0-11
40-9.0-7
115PL 80 20-6.1-11
20-6.5-11		 25-6.5-11
25-7.0-11
25-7.5-11 		30-7.0-11
30-7.5-11
30-8.0-11		 35-8.0-11
35-8.5-11
35-9.0-11		 40-9.0-11
40-10.0-11
90 20-6.1-11
20-6.5-11		 25-6.5-11
25-7.0-11
25-7.5-11 		30-7.0-11
30-7.5-11
30-8.0-11		 35-8.0-11
35-8.5-11
35-9.0-11		 40-10.0-11
40-9.0-7
100 20-6.5-11
20-7.0-11		 25-6.5-11
25-7.0-11
25-7.5-11 		30-7.0-11
30-7.5-11
30-8.0-11 		35-9.0-11
35-10.0-11
35-9.0-7		 40-10.0-11
40-9.0-7

RTSE DOUBLE ARM LUMINAIRES
ARM WIND RTSE 20 RTSE 25 RTSE 30 RTSE 35 RTSE 40
26PS 80 20-6.1-11
20-6.5-11		 25-6.1-11
25-6.5-11
 30-7.0-11
30-7.5-11
30-8.0-11		 35-8.0-11
35-8.5-11
35-9.0-11		 40-9.0-11
40-10.0-11
90 20-6.1-11
20-6.5-11		 25-6.5-11
25-7.0-11		 30-7.0-11
30-7.5-11
30-8.0-11		 35-8.5-11
35-9.0-11
35-10.0-11		 40-10.0-11
40-9.0-7
100 20-6.1-11
20-6.5-11		 25-6.5-11
25-7.0-11
25-7.5-11 		30-7.5-11
30-8.0-11		 35-9.0-11
35-10.0-11		 40-9.0-7
28PS 80 20-6.1-11
20-6.5-11		 25-6.5-11
25-7.0-11		 30-7.0-11
30-7.5-11
30-8.0-11		 35-8.5-11
35-9.0-11
35-10.0-11		 40-9.0-11
40-10.0-11
90 20-6.1-11
20-6.5-11		 25-6.5-11
25-7.0-11
25-7.5-11 		30-7.5-11
30-8.0-11		 35-8.5-11
35-9.0-11
35-10.0-11		 40-10.0-11
40-9.0-7
100 20-6.5-11
20-7.0-11		 25-7.0-11
25-7.5-11 		30-7.5-11
30-8.0-11		 35-9.0-11
35-10.0-11		 40-9.0-7
210PS 80 20-6.5-11
20-7.0-11		 25-6.5-11
25-7.0-11
25-7.5-11 		30-7.5-11
30-8.0-11
30-8.5-11		 35-9.0-11
35-10.0-11
35-9.0-7		 40-10.0-11
40-9.0-7
90 20-6.5-11
20-7.0-11		 25-6.5-11
25-7.0-11
25-7.5-11 		30-7.5-11
30-8.0-11		 35-8.5-11
35-9.0-7
 40-9.0-7
100 20-6.5-11
20-7.0-11		 25-7.0-11
25-7.5-11		 30-7.5-11
30-8.0-11		 35-9.0-7
 40-9.0-7
212PS 80 20-6.5-11
20-7.0-11		 25-7.0-11
25-7.5-11		 30-7.5-11
30-8.0-11		 35-9.0-11
35-10.0-11
 40-10.0-11
90 20-6.5-11
20-7.0-11		 25-7.0-11
25-7.5-11		 30-8.5-11
30-9.0-11		 35-10.0-11
35-9.0-7		 40-9.0-7
100 20-6.5-11
20-7.0-11		 25-7.0-11
25-7.5-11		 30-9.0-11 35-9.0-7 40-11.0-7
215PL 80 20-6.5-11
20-7.0-11		 25-7.0-11
25-7.5-11		 30-7.5-11
30-8.0-11		 35-10.0-11
35-9.0-7 		40-9.0-7
90 20-6.5-11
20-7.0-11		 25-7.0-11
25-7.5-11		 30-9.0-11 35-9.0-7 40-11.0-7
100 20-6.5-11
20-7.0-11		 25-7.5-11 30-10.0-11 35-9.0-7 40-11.0-7

Breakaway Bases


Note: For existing A.B. wth B.C. (10-1/2" - 12-15/16"), consult factory for modified transformer-base.

Breakaway Support Couplings


FINISHES


      Standard  
BRZ    Bronze    
BLK    Black    
GRY    Gray    
GRN    Green    
WHT    White    
P    Primed    
NA    Natural Aluminum    
  
           Galvanized  
G    Galvanized    
  
    K-KLAD  
K813    Bronze    
K821    Black    
K841    Gray    
K891    Green    
K881    White    
K845    Natural Aluminum    
  
    K-KLAD Over Galvanizing  
KZ13    Bronze    
KZ21    Black    
KZ41    Gray    
KZ91    Green    
KZ81    White    
KZ45    Natural Aluminum    
  
 1 YEAR WARRANTY  5 YEAR WARRANTY  10 YEAR WARRANTY 

OPTIONS
There are numerous options that can be ordered. Please indicate these selections under the options column in the catalog number. Example: WPR2-NC.

   Accessories  
BC    Base Cover    
NC    Nut Covers    
WPRP    Festoon Opening**    
LAB    Less Anchor Bolt    
VDI    Vibration Damper Internal    
  

   Optional Handholes  
58HH    5'' x 8'' Handhole*    
410HH    4'' x 10'' Handhole*    
  

   Extra Handholes  
XHH    Extra Handhole*    
  

   Embedment Pole Options  
E    Embedded Pole    
GS    Ground Sleeve    
CTE    Coal Tar Epoxy    
  
For Embedment Poles:
Recommended Mounting HeightRecommended Embedment Depth
20' - 35'5'
35' - 40'7'

Greater embedment depths are available upon request.

  * Please advise size, location, and orientation. (Handholes are restricted by size of pole shaft diameter)
** Located 24" above baseplate and same side as handhole. (No electrical included)

Printer Friendly View