Getting your brightest ideas off the ground®

COMPANY profile        standard        coating system       OUR commitment       Terms and Conditions       Warranty       ONLINE CATALOG       Contact Us THSP Square Tapered Steel Hinged Poles Pole Shaft The pole shaft is two section design, each section being fabricated from standard 11 gauge (0.1196"), 7 gauge (0.1793"), or 3 gauge (0.2391") steel. The pole shaft material is a weldable grade hot rolled commercial quality carbon steel with a guaranteed minimum yield strength of 55,000 psi after fabrication. Each section is one-piece construction with a full length longitudinal weld and is square in cross-section having a uniform taper of 0.10 inches of diameter change per foot of length. Base Plate The anchor base is fabricated from structural quality hot rolled carbon steel plate that meets or exceeds a minimum yield strength of 36,000 psi. The anchor base telescopes the pole shaft and is circumferentially welded top and bottom. All welds are performed in accordance with the American Welding Society specification AWS D1.1, latest edition. Anchor Bolts Anchor bolts are fabricated from commercial quality hot rolled carbon steel bar that meets or exceeds a minimum yield strength of 55,000 psi. Four properly sized anchor bolts, each with two regular hex nuts and washers, are furnished and shipped with all poles unless otherwise specified. Anchor bolts shall have the threaded end galvanized a minimum of 8 inches in accordance with ASTM A153. Fully galvanized anchor bolts are available upon request. Handhole An oval reinforced gasketed handhole, having a nominal 3" x 5" or 4" x 6-1/2" inside opening, located 1'-6" above the base, is standard on all poles. Optional 5" x 8" and 4" x 10" handholes are available (see options). A grounding provision is located inside the handhole ring. Finishes The Standard Finish is a polyester thermosetting powder coating applied to the surface of the substrate to a minimum of 3 mils for all color finishes. Hot dip Galvanized finish to a ASTM A123 specification or primed finish is also available. For optional finishes, see K-KLAD and K-KLAD Over Galvanizing. HOW TO ORDER When ordering KW lighting standards, mounting adaptors and accessories, be sure to specify the complete catalog number. Our catalog numbers reflect the precise specifications of the item ordered to ensure our customers will receive the product which meets their exact requirements. The following explanation of the catalog numbers will be helpful in placing orders: CATALOG LOGIC - ORDERING SAMPLE Catalog Number Nominal Height Pole Shaft Gauge Handhole Size Anchor Bolt Bolt Circle 80 MPH 90 MPH 100 MPH Ship WT. Hinge Point 'H'¹(ft.) 'H'²(ft.) Select THSP20-4.00-7 20 4.00 x 3.50 x 20.0 7 3 x 5 0.75 x 30 x 3 8 21.5 16.8 13.1 236 10 4.42 Configure THSP10-4.00-7 10 4.00 x 3.50 x 10.0 7 3 x 5 0.75 x 30 x 3 8 21.5 16.8 13.1 236 10 4.42 Configure THSP25-4.00-7 25 4.00 x 3.50 x 25.0 7 3 x 5 0.75 x 30 x 3 8 13.7 10.2 7.4 328 15 3.42 Configure THSP30-4.00-7 30 4.00 x 3.50 x 30.0 7 3 x 5 0.75 x 30 x 3 8 7.1 4.7 2.7 356 15 3.42 Configure THSP20-6.25-7 20 6.2 x 3.4 x 20.0 7 4 x 6.5 1.00 x 36 x 4 12.5 64 50 39.5 386 10 4.42 Configure THSP25-6.25-11 25 6.25 x 3.75 x 25.0 11 4 x 6.5 1.00 x 36 x 4 12.5 24 17 12 404 15 3.42 Configure THSP20-6.25-11 20 6.2 x 3.4 x 20.0 11 4 x 6.5 1.00 x 36 x 4 12.5 24 17 12 404 10 4.42 Configure THSP30-6.25-11 30 6.25 x 3.25 x 30.0 11 4 x 6.5 1.00 x 36 x 4 12.5 15.6 10.5 6.5 434 15 3.42 Configure THSP20-7.15-11 20 7.15 x 5.15 x 20.0 11 4 x 6.5 1.00 x 36 x 4 13.5 41.5 31 24 439 10 4.42 Configure THSP25-7.15-11 25 7.15 x 4.65 x 25.0 11 4 x 6.5 1.00 x 36 x 4 13.5 28 20.3 14.7 481 15 3.42 Configure THSP25-6.25-7 25 6.25 x 2.75 x 25.0 7 4 x 6.5 1.00 x 36 x 4 12.5 46 34.5 27 485 15 3.42 Configure THSP30-6.25-7 30 6.25 x 3.25 x 30.0 7 4 x 6.5 1.00 x 36 x 4 12.5 32.7 24 18 528 15 3.42 Configure THSP20-7.15-7 20 7.15 x 5.15 x 20.0 7 4 x 6.5 1.00 x 36 x 4 13.5 71 55 43 543 10 4.42 Configure THSP35-7.15-11 35 7.15 x 3.65 x 35.0 11 4 x 6.5 1.00 x 36 x 4 13.5 17.3 12.2 8.2 602 20 3.42 Configure THSP30-7.15-11 30 7.1 x 2.9 x 30.0 11 4 x 6.5 1.00 x 36 x 4 13.5 17.3 12.2 8.2 602 20 3.42 Configure THSP25-7.15-7 25 7.15 x 4.65 x 25.0 7 4 x 6.5 1.00 x 36 x 4 13.5 54 41 32 605 15 3.42 Configure THSP39-7.15-11 39 7.15 x 3.25 x 39.0 11 4 x 6.5 1.00 x 36 x 4 13.5 12.7 8.2 4.8 611 20 3.42 Configure THSP35-7.15-7 35 7.15 x 3.65 x 35.0 7 4 x 6.5 1.00 x 36 x 4 13.5 24.3 17.8 12.8 759 20 3.42 Configure THSP30-7.15-7 30 7.1 x 2.9 x 30.0 7 4 x 6.5 1.00 x 36 x 4 13.5 24.3 17.8 12.8 759 20 3.42 Configure THSP39-7.15-7 39 7.15 x 3.25 x 39.0 7 4 x 6.5 1.00 x 36 x 4 13.5 18.7 13.1 8.8 801 20 3.42 Configure FINISHES       Standard   BRZ     Bronze     BLK     Black     GRY     Gray     GRN     Green     WHT     White     P     Primed     NA     Natural Aluminum                   Galvanized   G     Galvanized            K-KLAD   K813     Bronze     K821     Black     K841     Gray     K891     Green     K881     White     K845     Natural Aluminum            K-KLAD Over Galvanizing   KZ13     Bronze     KZ21     Black     KZ41     Gray     KZ91     Green     KZ81     White     KZ45     Natural Aluminum         1 YEAR WARRANTY   5 YEAR WARRANTY   10 YEAR WARRANTY  MOUNTING DESIGNATIONS    Tenon Mount   2     2 3/8'' x 4'' TENON     3     2 7/8'' x 4'' TENON     3.5     3 1/2'' x 6'' TENON     4     4'' x 6'' TENON           Drill Mount   DM10     Drilled for 1 Luminaire     DM2090     Drilled for 2 Luminaires @ 90º     DM2180     Drilled for 2 Luminaires @ 180º     DM3090     Drilled for 3 Luminaires @ 90º     DM4090     Drilled for 4 Luminaires @ 90º           Open Mount   OT     Open Top     OTC     Open Top includes Pole Cap           Gain Mount   1GSS4     (1) CXA     2GSS4     (2) CXA's located on the Same Side     3GSS4     (3) CXA's located on the Same Side     4GSS4     (4) CXA's located on the Same Side     2GBB4     (2) CXA's located Back to Back     4GBB4     (4) CXA's located Back to Back     1GSS9     (1) CXASQ     2GSS9     (2) CXASQ's located on the Same Side     3GSS9     (3) CXASQ's located on the Same Side     4GSS9     (4) CXASQ's located on the Same Side     2GBB9     (2) CXASQ's located Back to Back     4GBB9     (4) CXASQ's located Back to Back        OPTIONS There are numerous options that can be ordered. Please indicate these selections under the options column in the catalog number. Example: CPL-WPR2-BC.    Accessories   BC     Base Cover     CPL     Threaded Coupling*     NPL     Threaded Nipple*     WPRP     Festoon Opening**     LW     Lowering Winch***     LAB     Less Anchor Bolt     VDI     Vibration Damper Internal        Poles ordered with a lowering winch will be provided with one device per order unless otherwise requested.    Optional Handholes   58HH     5'' x 8'' Handhole*     410HH     4'' x 10'' Handhole*           Extra Handholes   XHH     Extra Handhole*           Additional Simplex   1S     1 @ 0º *     2S     2 @ 180º *     3S     3 @ 90º *     4S     4 @ 90º *            * Please advise size, location, and orientation. (Handholes are restricted by size of pole shaft diameter)   ** Located 24" above baseplate and same side as handhole. (No electrical included) *** KW Industries recommends the use of a KW lowering winch for maintenance on THSP series poles. PACKAGING Immediately after coating, the lighting standard including the baseplate shall be wrapped in heavy corrugation specially designed and sized to achieve maximum protection in transit. KW Industries, Inc. coating process system and stringent quality control procedures provide our customer the finest quality lighting standards in the industry. Printer Friendly View