[Pole Shaft]
The pole shaft is one piece construction, being fabricated from a weldable grade carbon steel structural tubing which has a
uniform wall thickness of 11 gauge (0.1196"), 7 gauge (0.1793"), or 3 gauge (0.2391").
The pole shaft material shall conform to ASTM A-500 Grade C with a minimum yield strength of 50,000 psi.
The pole shaft has a full length longitudinal resistance weld and is uniformly square in cross-section with flat sides,
small corner radii and excellent torsional properties.
|
[Anchor Bolts]
Anchor bolts are fabricated from commercial quality hot rolled carbon steel bar that meets or exceeds a minimum yield strength of 55,000 psi. Four properly sized anchor bolts, each with two regular hex nuts and washers, are furnished and shipped with all poles unless otherwise specified. Anchor bolts shall have the threaded end galvanized a minimum of 8 inches in accordance with ASTM A-153.
Fully galvanized anchor bolts are available upon request.
|
[Base Plate]
The anchor base is fabricated from structural quality hot rolled carbon steel plate that meets or
exceeds a minimum yield strength of 36,000 psi. The anchor base telescopes the pole shaft and is circumferentially welded top and bottom.
All welds are performed in accordance with the American Welding Society specification AWS D1.1, latest edition.
|
[Handhole]
An oval reinforced gasketed handhole, having a nominal 3" x 5" or 4" x 6-1/2" inside opening,
located 1'-6" above base, is standard on all poles. Optional 5" x 8" and 4" x 10" handholes are available.
A grounding provision is located inside the handhole ring.
|
[Finish]
All exterior metal surfaces are mechanically cleaned to remove all oxides and contaminants prior to coating. The standard finish is a polyester thermosetting powder coating applied to the surface of the substrate to a minimum of 3 mils for all color finishes.
Galvanizing is available upon request.
|
|
FINISH
| | P - Primer | | BK - Black Finish Color | | BZ - Bronze Finish Color | | GN - Green Finish Color | | GY - Gray Finish Color | | LA - Dark Natural Aluminum | | LM - Natural Aluminum | | G - Hot Dipped Galvanized | | WH - White Finish Color | | CT - Custom Color | | G/BK - Black over Galvanized | | G/BZ - Bronze over Galvanized | | G/GN - Green over Galvanized | | G/GY - Gray over Galvanized | | G/LM - Natural Aluminum over galvanized | | G/WH - White over Galvanized | | G/CT - Custom over Galvanized |
MOUNTING DESIGNATIONS
| | OT - Open Top | | PC - Pole Cap | | 2 - 2 3/8” OD Tenon | | 3 - 2 7/8” OD Tenon | | 3.5 - 3 1/2” OD Tenon | | 4 - 4” OD x 6” Tenon | | DM - Drilled Mount | | DM10 - Drilled for 1 Luminaire | | DM29 - Drilled for 2 Luminaires at 90º | | DM28 - Drilled for 2 Luminaires at 180º | | DM39 - Drilled for 3 Luminaires at 90º | | DM49 - Drilled for 4 Luminaires at 90º | | WP - Wood Pole |
* Standard location for DM10 is 90º to the right of the handhole.
OPTIONS
| | XHH - Extra Handhole | | WPRP - Festoon Opening | | CPL - Threaded Coupling | | NPL - Threaded Nipple | | VDI - Vibration Damper Internal | | BC - Base Cover | |
| LAB - Less Anchor Bolt | | EMB - Embedded Pole |
|
