Getting your brightest ideas off the ground®

I dyed the and closure and left it overnight, and washed it out the next morning, the human hair wigs dyed well and the was still black. So when I added developer, I left the human hair extensions to sit for 6 hours and washed it out. This was great but please if you guys could please get the same from the bundles down to the closure human hair will be awesome. I will definitely be ordering this again but next time I will just make sure I let the human hair wigs uk for hair bundles uk. Our Romance Curl Silk Top Glueless brazilian hair uk and great for wearing your curly.
      COMPANY profile


       coating system

      OUR commitment

      Terms and Conditions



      Contact Us

Round Non-Tapered Steel Poles
Pole Shaft
The pole shaft is one piece construction, being fabricated from a weldable grade carbon steel structural tubing which has a uniform wall thickness of 11 gauge (0.1196") or 7 gauge (0.1793"). The pole shaft material shall conform to ASTM A500 Grade C with a minimum yield strength of 50,000 psi. The pole shaft has a full length longitudinal resistance weld and is uniformly cylindrical in cross-section with round sides and excellent torsional properties.
Base Plate
The anchor base is fabricated from structural quality hot rolled carbon steel plate that meets or exceeds a minimum yield strength of 36,000 psi. The anchor base telescopes the pole shaft and is circumferentially welded top and bottom. All welds are performed in accordance with the American Welding Society specification AWS D1.1, latest edition.
Anchor Bolts
Anchor bolts are fabricated from commercial quality hot rolled carbon steel bar that meets or exceeds a minimum yield strength of 55,000 psi. Four properly sized anchor bolts, each with two regular hex nuts and washers, are furnished and shipped with all poles unless otherwise specified. Anchor bolts shall have the threaded end galvanized a minimum of 8 inches in accordance with ASTM A153. Fully galvanized anchor bolts are available upon request.
An oval reinforced gasketed handhole, having a nominal 2" x 4" or 3" x 5" inside opening, located 1'-6" above base, is standard on all poles. A grounding provision is located inside the handhole ring.
The Standard Finish is a polyester thermosetting powder coating applied to the surface of the substrate to a minimum of 3 mils for all color finishes. Hot dip Galvanized finish to a ASTM A123 specification or primed finish is also available. For optional finishes, see K-KLAD and
K-KLAD Over Galvanizing.

When ordering KW lighting standards, mounting adaptors and accessories, be sure to specify the complete catalog number. Our catalog numbers reflect the precise specifications of the item ordered to ensure our customers will receive the product which meets their exact requirements.
The following explanation of the catalog numbers will be helpful in placing orders:


Catalog Number Nominal
Pole Shaft Gauge Handhole
Anchor Bolt Bolt
RSP10-4.0-11104.00 x 10.0112 x 40.75 x 17 x 38312419.578Configure
RSP10-4.5-11104.50 x 10.0113 x 50.75 x 17 x 384031.52584Configure
RSP10-5.0-11105.0 x 10.0113 x 51.00 x 36 x 4115140.532.5139Configure
RSP12-4.0-11124.00 x 12.0112 x 40.75 x 17 x 3828.923.419.273Configure
RSP12-4.5-11124.50 x 12.0113 x 50.75 x 17 x 38342721.596Configure
RSP12-5.0-11125.0 x 12.0113 x 51.00 x 36 x 4114333.527153Configure
RSP14-4.0-11144.00 x 14.0112 x 40.75 x 17 x 3823.619.115.699Configure
RSP14-4.5-11144.50 x 14.0113 x 50.75 x 17 x 38282217108Configure
RSP14-5.0-11145.0 x 14.0113 x 51.00 x 36 x 411362822.5166Configure
RSP15-4.0-11154.00 x 15.0112 x 40.75 x 17 x 3818.114.511.888Configure
RSP15-4.5-11154.50 x 15.0113 x 50.75 x 17 x 3826.520.516.398Configure
RSP15-5.0-11155.0 x 15.0113 x 51.00 x 36 x 411332620.5173Configure
RSP15-5.0-7155.0 x 15.073 x 51.00 x 36 x 411503931.5222Configure
RSP16-4.0-11164.00 x 16.0112 x 40.75 x 17 x 3816.513.210.693Configure
RSP16-4.5-11164.50 x 16.0113 x 50.75 x 17 x 3824.418.814.8120Configure
RSP16-5.56-7165.56 x 1673 x 51.00 x 42 x 410473729254Configure
RSP16-5.0-11165.0 x 16.0113 x 51.00 x 36 x 4113124.219.4179Configure
RSP16-5.0-7165.0 x 16.073 x 51.00 x 36 x 411473729232Configure
RSP18-4.0-11184.00 x 18.0112 x 40.75 x 17 x 3813.710.88.6103Configure
RSP18-4.5-11184.50 x 18.0113 x 50.75 x 17 x 38211612.5132Configure
RSP18-5.0-11185.0 x 18.0113 x 51.00 x 36 x 411272116.5192Configure
RSP18-5.0-7185.0 x 18.073 x 51.00 x 36 x 411403125.2252Configure
RSP20-4.0-11204.00 x 20.0112 x 40.75 x 17 x 3811.48.96.9123Configure
RSP20-4.5-11204.50 x 20.0113 x 50.75 x 30 x 3815.512.29.6135Configure
RSP20-5.0-11205.00 x 20.0113 x 51.00 x 36 x 41120.31612.7189Configure
RSP20-5.0-7205.00 x 20.073 x 51.00 x 36 x 41128.222.418253Configure
RSP22-4.5-11224.50 x 22.0113 x 50.75 x 30 x 381310.17.8147Configure
RSP22-4.0-11224.00 x 22.0112 x 40.75 x 17 x 3875.13.7148Configure
RSP22-5.0-11225.00 x 22.0113 x 51.00 x 36 x 41117.313.510.5202Configure
RSP22-5.0-7225.00 x 22.073 x 51.00 x 36 x 41124.219.215.3272Configure
RSP24-4.0-11244.00 x 24.0112 x 40.75 x 17 x 3875.13.7148Configure
RSP24-4.5-11244.50 x 24.0113 x 50.75 x 30 x 3810.98.36.3158Configure
RSP24-5.0-11245.00 x 24.0113 x 51.00 x 36 x 41114.611.38.6215Configure
RSP24-5.0-7245.00 x 24.073 x 51.00 x 36 x 41120.916.412.9292Configure
RSP25-4.0-11254.00 x 25.0112 x 40.75 x 17 x 3875.13.7148Configure
RSP25-4.5-11254.50 x 25.0113 x 50.75 x 30 x 38107.55.5164Configure
RSP25-5.0-11255.00 x 25.0113 x 51.00 x 36 x 41113.510.37.8221Configure
RSP25-5.0-7255.00 x 25.073 x 51.00 x 36 x 41119.415.111.8301Configure
RSP26-4.5-11264.50 x 26.0113 x 50.75 x 30 x 389.16.74.9170Configure
RSP26-5.0-11265.00 x 26.0113 x 51.00 x 36 x 41112.49.37228Configure
RSP26-5.0-7265.00 x 26.073 x 51.00 x 36 x 4111813.910.8311Configure
RSP28-4.5-11284.50 x 28.0113 x 50.75 x 30 x 387.45.33.6182Configure
RSP28-5.0-11285.00 x 28.0113 x 51.00 x 36 x 41110.47.65.5240Configure
RSP28-5.0-7285.00 x 28.073 x 51.00 x 36 x 41115.411.78.9330Configure
RSP30-4.5-11304.50 x 30.0113 x 50.75 x 30 x 385.33.52.2193Configure
RSP30-5.0-11305.00 x 30.0113 x 51.00 x 36 x 4117.65.33.6253Configure
RSP30-5.0-7305.00 x 30.073 x 51.00 x 36 x 41111.58.56.2349Configure
RSP35-5.0-7355.00 x 35.073 x 51.00 x 36 x 41174.62.8397Configure


BRZ    Bronze    
BLK    Black    
GRY    Gray    
GRN    Green    
WHT    White    
P    Primed    
NA    Natural Aluminum    

G    Galvanized    

K813    Bronze    
K821    Black    
K841    Gray    
K891    Green    
K881    White    
K845    Natural Aluminum    

    K-KLAD Over Galvanizing  
KZ13    Bronze    
KZ21    Black    
KZ41    Gray    
KZ91    Green    
KZ81    White    
KZ45    Natural Aluminum    


   Tenon Mount  
2    2 3/8'' x 4'' TENON    
3    2 7/8'' x 4'' TENON    
3.5    3 1/2'' x 6'' TENON    
4    4'' x 6'' TENON    
4x4    4'' x 4'' TENON    

   Drill Mount  
DM10    Drilled for 1 Luminaire    
DM2090    Drilled for 2 Luminaires @ 90º    
DM2180    Drilled for 2 Luminaires @ 180º    
DM3090    Drilled for 3 Luminaires @ 90º    
DM3120    Drilled for 3 Luminaires @ 120º    
DM4090    Drilled for 4 Luminaires @ 90º    

   Open Mount  
OT    Open Top    
OTC    Open Top includes Pole Cap    

   Gain Mount  
1GSS4    (1) CXA    
2GSS4    (2) CXA's located on the Same Side    
3GSS4    (3) CXA's located on the Same Side    
4GSS4    (4) CXA's located on the Same Side    
2GBB4    (2) CXA's located Back to Back    
4GBB4    (4) CXA's located Back to Back    
1GSS9    (1) CXASQ    
2GSS9    (2) CXASQ's located on the Same Side    
3GSS9    (3) CXASQ's located on the Same Side    
4GSS9    (4) CXASQ's located on the Same Side    
2GBB9    (2) CXASQ's located Back to Back    
4GBB9    (4) CXASQ's located Back to Back    

There are numerous options that can be ordered. Please indicate these selections under the options column in the catalog number. Example: CPL-WPR2-BC.

BC    Base Cover    
CPL    Threaded Coupling*    
NPL    Threaded Nipple*    
WPRP    Festoon Opening**    
LAB    Less Anchor Bolt    
VDI    Vibration Damper Internal    

   Optional Handholes  
SF35HH    3'' x 5'' Semi-Flush Handhole    

   Extra Handholes  
XHH    Extra Handhole*    

   Embedment Pole Options  
E    Embedded Pole    
GS    Ground Sleeve    
CTE    Coal Tar Epoxy    

For Embedment Poles:
Recommended Mounting HeightRecommended Embedment Depth
Less than 20'4'
20' - 33'6'
Greater than 33'7'

Greater embedment depths are available upon request.

   Additional Simplex  
1S    1 @ 0º *    
2S    2 @ 180º *    
3S    3 @ 90º *    
4S    4 @ 90º *    

   Optional Cast Steel Base Plate  
CSBP    Cast Steel Base Plate    

  * Please advise size, location, and orientation. (Handholes are restricted by size of pole shaft diameter)
** Located 24" above baseplate and same side as handhole. (No electrical included)

Immediately after coating, the lighting standard including the baseplate shall be wrapped in heavy corrugation specially designed and sized to achieve maximum protection in transit.
KW Industries, Inc. coating process system and stringent quality control procedures provide our customer the finest quality lighting standards in the industry.

Printer Friendly View