WJM Poles

ST - SQUARE TAPERED STEEL

[Pole Shaft]
The pole shaft is one or two section design, each section being fabricated from standard 11 gauge (0.1196"), 7 gauge (0.1793"), or 3 gauge (0.2391") steel. The pole shaft material is a weldable grade hot rolled commercial quality carbon steel with a guaranteed minimum yield strength of 55,000 psi after fabrication. Each section is one-piece construction with a full length longitudinal weld and is square in cross-section having a uniform taper of 0.10 inches of diameter change per foot of length.

[Anchor Bolts]
Anchor bolts are fabricated from commercial quality hot rolled carbon steel bar that meets or exceeds a minimum yield strength of 55,000 psi. Four properly sized anchor bolts, each with two regular hex nuts and washers, are furnished and shipped with all poles unless otherwise specified. Anchor bolts shall have the threaded end galvanized a minimum of 8 inches in accordance with ASTM A-153. Fully galvanized anchor bolts are available upon request.

[Base Plate]
The anchor base is fabricated from structural quality hot rolled carbon steel plate that meets or exceeds a minimum yield strength of 36,000 psi. The anchor base telescopes the pole shaft and is circumferentially welded top and bottom. All welds are performed in accordance with the American Welding Society specification AWS D1.1, latest edition.

[Handhole]
An oval reinforced gasketed handhole, having a nominal 3" x 5" or 4" x 6-1/2" inside opening, located 1'-6" above base, is standard on all poles. A grounding provision is located inside the handhole ring.

[Finish]
All exterior metal surfaces are mechanically cleaned to remove all oxides and contaminants prior to coating. The standard finish is a polyester thermosetting powder coating applied to the surface of the substrate to a minimum of 3 mils for all color finishes. Galvanizing is available upon request.

FINISH

	P - Primer
	BK - Black Finish Color
	BZ - Bronze Finish Color
	GN - Green Finish Color
	GY - Gray Finish Color
	LA - Dark Natural Aluminum
	LM - Natural Aluminum
	G - Hot Dipped Galvanized
	WH - White Finish Color
	CT - Custom Color
	G/BK - Black over Galvanized
	G/BZ - Bronze over Galvanized
	G/GN - Green over Galvanized
	G/GY - Gray over Galvanized
	G/LM - Natural Aluminum over galvanized
	G/WH - White over Galvanized
	G/CT - Custom over Galvanized

MOUNTING DESIGNATIONS

	OT - Open Top
	PC - Pole Cap
	2 - 2 3/8� OD Tenon
	3 - 2 7/8� OD Tenon
	3.5 - 3 1/2� OD Tenon
	4 - 4� OD x 6� Tenon
	DM - Drilled Mount
	DM10 - Drilled for 1 Luminaire
	DM29 - Drilled for 2 Luminaires at 90º
	DM28 - Drilled for 2 Luminaires at 180º
	DM39 - Drilled for 3 Luminaires at 90º
	DM49 - Drilled for 4 Luminaires at 90º
	WP - Wood Pole

* Standard location for DM10 is 90� to the right of the handhole.

OPTIONS

	XHH - Extra Handhole
	WPRP - Festoon Opening
	CPL - Threaded Coupling
	NPL - Threaded Nipple
	VDI - Vibration Damper Internal
	BC - Base Cover

	LAB - Less Anchor Bolt
	EMB - Embedded Pole

SORT THE LIST BELOW BASED ON YOUR PREFERENCE BY CLICKING THE COLUMN TITLE

Height (ft.)	Catalog Number	Pole Shaft (in.) x (in.) x (ft.)	Shaft Gauge	Bolt Circle (in.)	Anchor Bolt (in.) x (in.) x (in.)	Handhole Size (in.)	80 MPH (ft.²)	90 MPH (ft.²)	100 MPH (ft.²)	Ship Wt. (lbs)	Select
20	ST5631120	5.63 x 3.65 x 20.0	11	10.75	1.00 x 36 x 4	3 x 5	28	22	17	205	Configure
25	ST6441125	6.44 x 3.97 x 25.0	11	12.5	1.00 x 36 x 4	4 x 6.5	25	18	13	282	Configure
30	ST6441130	6.44 x 3.47 x 30.0	11	12.5	1.00 x 36 x 4	4 x 6.5	16	11	7	312	Configure
30	ST7320730	7. 32 x 4.35 x 30.0	7	13.5	1.00 x 36 x 4	4 x 6.5	37	27	20	505	Configure
35	ST7320735	7. 32 x 3.86 x 35.0	7	13.5	1.00 x 36 x 4	4 x 6.5	25	18	13	554	Configure
39	ST7320739	7. 32 x 3.46 x 39.0	7	13.5	1.00 x 36 x 4	4 x 6.5	19	13	9	589	Configure
30	ST7321130	7. 32 x 4.35 x 30.0	11	13.5	1.00 x 36 x 4	4 x 6.5	19	13	9	357	Configure
35	ST7321135	7. 32 x 3.86 x 35.0	11	13.5	1.00 x 36 x 4	4 x 6.5	18	13	9	419	Configure
39	ST7321139	7. 32 x 3.46 x 39.0	11	13.5	1.00 x 36 x 4	4 x 6.5	13	9	5	413	Configure
35	ST8000735	8.31 x 4.85 x 35.0	7	14.75	1.25 x 42 x 6	4 x 6.5	14	8	3	715	Configure
39	ST8310739	8.31 x 4.45 x 39.0	7	14.75	1.25 x 42 x 6	4 x 6.5	14	8	3	715	Configure
45	ST8310745	8.31 x 6.20 x 21.3 / 6.57 x 4.10 x 25.0	7	14.75	1.25 x 42 x 6	4 x 6.5	14	8	3	715	Configure
50	ST8310750	8.31 x 6.20 x 21.3 / 6.57 x 3.60 x 30.0	7	14.75	1.25 x 42 x 6	4 x 6.5	8	4	0	732	Configure