Printer Friendly Version


[Pole Shaft]
The pole shaft is one or two section design, each section being fabricated from standard 11 gauge (0.1196"), 7 gauge (0.1793"), or 3 gauge (0.2391") steel. The pole shaft material is a weldable grade hot rolled commercial quality carbon steel with a guaranteed minimum yield strength of 55,000 psi after fabrication. Each section is one-piece construction with a full length longitudinal weld and is square in cross-section having a uniform taper of 0.10 inches of diameter change per foot of length.

[Anchor Bolts]
Anchor bolts are fabricated from commercial quality hot rolled carbon steel bar that meets or exceeds a minimum yield strength of 55,000 psi. Four properly sized anchor bolts, each with two regular hex nuts and washers, are furnished and shipped with all poles unless otherwise specified. Anchor bolts shall have the threaded end galvanized a minimum of 8 inches in accordance with ASTM A-153. Fully galvanized anchor bolts are available upon request.

[Base Plate]
The anchor base is fabricated from structural quality hot rolled carbon steel plate that meets or exceeds a minimum yield strength of 36,000 psi. The anchor base telescopes the pole shaft and is circumferentially welded top and bottom. All welds are performed in accordance with the American Welding Society specification AWS D1.1, latest edition.

An oval reinforced gasketed handhole, having a nominal 3" x 5" or 4" x 6-1/2" inside opening, located 1'-6" above base, is standard on all poles. A grounding provision is located inside the handhole ring.

All exterior metal surfaces are mechanically cleaned to remove all oxides and contaminants prior to coating. The standard finish is a polyester thermosetting powder coating applied to the surface of the substrate to a minimum of 3 mils for all color finishes. Galvanizing is available upon request.


   P - Primer
BK - Black Finish Color
BZ - Bronze Finish Color
GN - Green Finish Color
GY - Gray Finish Color
LA - Dark Natural Aluminum
LM - Natural Aluminum
G - Hot Dipped Galvanized
WH - White Finish Color
CT - Custom Color
G/BK - Black over Galvanized
G/BZ - Bronze over Galvanized
G/GN - Green over Galvanized
G/GY - Gray over Galvanized
G/LM - Natural Aluminum over galvanized
G/WH - White over Galvanized
G/CT - Custom over Galvanized


   OT - Open Top
PC - Pole Cap
2 - 2 3/8 OD Tenon
3 - 2 7/8 OD Tenon
3.5 - 3 1/2 OD Tenon
4 - 4 OD x 6 Tenon
DM - Drilled Mount
DM10 - Drilled for 1 Luminaire
DM29 - Drilled for 2 Luminaires at 90º
DM28 - Drilled for 2 Luminaires at 180º
DM39 - Drilled for 3 Luminaires at 90º
DM49 - Drilled for 4 Luminaires at 90º
WP - Wood Pole

* Standard location for DM10 is 90 to the right of the handhole.


   XHH - Extra Handhole
WPRP - Festoon Opening
CPL - Threaded Coupling
NPL - Threaded Nipple
VDI - Vibration Damper Internal
BC - Base Cover
LAB - Less Anchor Bolt
EMB - Embedded Pole


Catalog Number Pole Shaft
(in.) x (in.) x (ft.)
Bolt Circle
Anchor Bolt
(in.) x (in.) x (in.)
Handhole Size
80 MPH
90 MPH
100 MPH
Ship Wt.
20ST56311205.63 x 3.65 x 20.01110.751.00 x 36 x 43 x 5282217205Configure
25ST64411256.44 x 3.97 x 25.01112.51.00 x 36 x 44 x 6.5251813282Configure
30ST64411306.44 x 3.47 x 30.01112.51.00 x 36 x 44 x 6.516117312Configure
30ST73211307. 32 x 4.35 x 30.01113.51.00 x 36 x 44 x 6.519139357Configure
30ST73207307. 32 x 4.35 x 30.0713.51.00 x 36 x 44 x 6.5372720505Configure
35ST73211357. 32 x 3.86 x 35.01113.51.00 x 36 x 44 x 6.518139419Configure
35ST73207357. 32 x 3.86 x 35.0713.51.00 x 36 x 44 x 6.5251813554Configure
35ST80007358.31 x 4.85 x 35.0714.751.25 x 42 x 64 x 6.51483715Configure
39ST73211397. 32 x 3.46 x 39.01113.51.00 x 36 x 44 x 6.51395413Configure
39ST73207397. 32 x 3.46 x 39.0713.51.00 x 36 x 44 x 6.519139589Configure
39ST83107398.31 x 4.45 x 39.0714.751.25 x 42 x 64 x 6.51483715Configure
45ST83107458.31 x 6.20 x 21.3 /
6.57 x 4.10 x 25.0
714.751.25 x 42 x 64 x 6.51483715Configure
50ST83107508.31 x 6.20 x 21.3 /
6.57 x 3.60 x 30.0
714.751.25 x 42 x 64 x 6.5840732Configure