RTS - ROADWAY STANDARD WITH RISER ARM


[Pole Shaft]
The pole shaft is one or two section design, each section being fabricated from standard 11 gauge (0.1196"), 7 gauge (0.1793"), or 3 gauge (0.2391") steel. The pole shaft material is a weldable grade hot rolled commercial quality carbon steel with a guaranteed minimum yield strength of 55,000 psi after fabrication. Each section is one-piece construction with a full length longitudinal weld and is cylindrical in cross-section having a uniform taper of 0.14 inches of diameter change per foot of length.


[Anchor Bolts]
Anchor bolts are fabricated from commercial quality hot rolled carbon steel bar that meets or exceeds a minimum yield strength of 55,000 psi. Four properly sized anchor bolts, each with two regular hex nuts and washers, are furnished and shipped with all poles unless otherwise specified. Anchor bolts shall have the threaded end galvanized a minimum of 8 inches in accordance with ASTM A-153. Fully galvanized anchor bolts are available upon request.


[Base Plate]
The anchor base is fabricated from structural quality hot rolled carbon steel plate that meets or exceeds a minimum yield strength of 36,000 psi. The anchor base telescopes the pole shaft and is circumferentially welded top and bottom. All welds are performed in accordance with the American Welding Society specification AWS D1.1, latest edition.


[Handhole]
An oval reinforced gasketed handhole, having a nominal 3" x 5" or 4" x 6-1/2" inside opening, located 1'-6" above base, is standard on all poles. Optional 5" x 8" and 4" x 10" handholes are available (see options). A grounding location is provided inside the handhole ring.


[Finish]
All exterior metal surfaces are mechanically cleaned to remove all oxides and contaminants prior to coating. The standard finish is a polyester thermosetting powder coating applied to the surface of the substrate to a minimum of 3 mils for all color finishes. Galvanizing is available upon request.













FINISH


   P - Primer
BK - Black Finish Color
BA - Brush Aluminum
BZ - Bronze Finish Color
GY - Gray Finish Color
LM - Natural Aluminum
GN - Green Finish Color
WH - White Finish Color
G - Hot Dipped Galvanized
G/BK - Black over Galvanized
CT - Custom Color
G/BZ - Bronze over Galvanized
G/GN - Green over Galvanized
G/GY - Gray over Galvanized
G/LM - Natural Aluminum over galvanized
G/WH - White over Galvanized
G/CT - Custom over Galvanized



OPTIONS


   XHH - Extra Handhole
WPRP - Festoon Opening
CPL - Threaded Coupling
NPL - Threaded Nipple
BC - Base Cover
NC - Nut Covers
LAB - Less Anchor Bolt
EMB - Embedded Pole
VDI - Vibration Damper Internal




SORT THE LIST BELOW BASED ON YOUR PREFERENCE BY CLICKING THE COLUMN TITLE

Mounting
Height
Catalog Number Base
Diameter
Gauge Bolt
Circle
Anchor Bolt Handhole
Size
Ship
WT.
20RTS61011206.10119.50.75 x 30 x 33 x 5.0149
20RTS65011206.50119.51.00 x 36 x 44 x 6.5205
25RTS61011256.10119.50.75 x 30 x 33 x 5.0173
25RTS65011256.50119.50.75 x 30 x 34 x 6.5204
25RTS68011256.8011100.75 x 30 x 34 x 6.5190
25RTS70011256.8011101.00 x 36 x 44 x 6.5230
30RTS68011306.8011100.75 x 30 x 34 x 6.5213
30RTS70011307.0011101.00 x 36 x 44 x 6.5253
30RTS75011307.501110.51.00 x 36 x 44 x 6.5265
30RTS80011308.1011111.00 x 36 x 44 x 6.5293
30RTS85011308.501111.51.00 x 36 x 44 x 6.5309
35RTS100113510.01113.51.00 x 36 x 44 x 6.5458
35RTS75011357.501110.51.00 x 36 x 44 x 6.5283
35RTS80011358.1011111.00 x 36 x 44 x 6.5311
35RTS85011358.501111.51.00 x 36 x 44 x 6.5338
35RTS90011359.001112.51.00 x 36 x 44 x 6.5358
35RTS90007359.000712.51.25 x 42 x 64 x 6.5534
40RTS80011408.001112.51.00 x 36 x 44 x 6.5327
40RTS90011409.001112.51.00 x 36 x 44 x 6.5376
40RTS10011409.001113.51.00 x 36 x 44 x 6.5480
40RTS90007409.000712.51.25 x 42 x 64 x 6.5597