Printer Friendly Version

RTU - ROADWAY STANDARD WITH UPSWEEP ARM


[Pole Shaft]
The pole shaft is one or two section design, each section being fabricated from standard 11 gauge (0.1196"), 7 gauge (0.1793"), or 3 gauge (0.2391") steel. The pole shaft material is a weldable grade hot rolled commercial quality carbon steel with a guaranteed minimum yield strength of 55,000 psi after fabrication. Each section is one-piece construction with a full length longitudinal weld and is cylindrical in cross-section having a uniform taper of 0.14 inches of diameter change per foot of length.


[Anchor Bolts]
Anchor bolts are fabricated from commercial quality hot rolled carbon steel bar that meets or exceeds a minimum yield strength of 55,000 psi. Four properly sized anchor bolts, each with two regular hex nuts and washers, are furnished and shipped with all poles unless otherwise specified. Anchor bolts shall have the threaded end galvanized a minimum of 8 inches in accordance with ASTM A-153. Fully galvanized anchor bolts are available upon request.


[Base Plate]
The anchor base is fabricated from structural quality hot rolled carbon steel plate that meets or exceeds a minimum yield strength of 36,000 psi. The anchor base telescopes the pole shaft and is circumferentially welded top and bottom. All welds are performed in accordance with the American Welding Society specification AWS D1.1, latest edition.


[Handhole]
An oval reinforced gasketed handhole, having a nominal 3" x 5" or 4" x 6-1/2" inside opening, located 1'-6" above base, is standard on all poles. Optional 5" x 8" and 4" x 10" handholes are available (see options). A grounding location is provided inside the handhole ring.


[Finish]
All exterior metal surfaces are mechanically cleaned to remove all oxides and contaminants prior to coating. The standard finish is a polyester thermosetting powder coating applied to the surface of the substrate to a minimum of 3 mils for all color finishes. Galvanizing is available upon request.













FINISH


   P - Primer
BK - Black Finish Color
BZ - Bronze Finish Color
LA - Dark Natural Aluminum
GY - Gray Finish Color
LM - Natural Aluminum
GN - Green Finish Color
WH - White Finish Color
G - Hot Dipped Galvanized
G/BK - Black over Galvanized
CT - Custom Color
G/BZ - Bronze over Galvanized
G/GN - Green over Galvanized
G/GY - Gray over Galvanized
G/LM - Natural Aluminum over galvanized
G/WH - White over Galvanized
G/CT - Custom over Galvanized



OPTIONS


   XHH - Extra Handhole
WPRP - Festoon Opening
CPL - Threaded Coupling
NPL - Threaded Nipple
VDI - Vibration Damper Internal
BC - Base Cover
NC - Nut Covers
LAB - Less Anchor Bolt
EMB - Embedded Pole




SORT THE LIST BELOW BASED ON YOUR PREFERENCE BY CLICKING THE COLUMN TITLE

Mounting
Height
Catalog Number Base
Diameter
Gauge Bolt
Circle
Anchor Bolt Handhole
Size
Ship
WT.
Select
20RTU61011206.10119.51.00 x 36 x 43 x 5.0149Configure
20RTU65011206.50119.51.00 x 36 x 44 x 6.5205Configure
25RTU61011256.10119.51.00 x 36 x 43 x 5.0173Configure
25RTU65011256.50119.51.00 x 36 x 44 x 6.5204Configure
25RTU68011256.8011101.00 x 36 x 44 x 6.5190Configure
25RTU70011256.8011101.00 x 36 x 44 x 6.5230Configure
30RTU68011306.8011101.00 x 36 x 44 x 6.5213Configure
30RTU70011307.0011101.00 x 36 x 44 x 6.5253Configure
30RTU75011307.501110.51.00 x 36 x 44 x 6.5265Configure
30RTU80011308.1011111.00 x 36 x 44 x 6.5293Configure
35RTU75011357.501110.51.00 x 36 x 44 x 6.5283Configure
35RTU80011358.1011111.00 x 36 x 44 x 6.5311Configure
35RTU85011358.501111.51.00 x 36 x 44 x 6.5338Configure
35RTU90011359.001112.51.00 x 36 x 44 x 6.5358Configure
40RTU90011409.001112.51.00 x 36 x 44 x 6.5376Configure
40RTU10011409.001113.51.00 x 36 x 44 x 6.5480Configure
40RTU90007409.000712.51.25 x 42 x 64 x 6.5597Configure